Follow

How do I use my SOURCE nail XL - Signature Kit (SOURCE volt Max)?

Watch a video on how to use your SOURCE nail XL

How to use as a Portable eNail

How to Fill Your Bubbler

  1. Remove the glass bubbler from the attachment (gently pull from the attachment).
  2. Pour 1/4 oz. of water into the mouthpiece, or until the bubbler is less than 1/4 full.
  3. If some water drops to the bottom chamber of the bubbler, that's ok, but you can tip forward slowly to let the excess water drip down.

How to Prep and Power On

SOURCE_volt_Max_battery_front_.jpg

  1. Attach the SOURCE nail XL attachment to your SOURCE volt Max battery.
  2. With the glass bubbler removed and screw your desired SOURCE nail atomizer clockwise unto the SOURCE nail XL attachment.
  3. Replace the glass bubbler after it's filled with water.
  4. Press the Power Button on your SOURCE volt Max battery sequentially 5 times to turn on.

Using your SOURCE volt Max Battery in Temp Control Mode

Using your Battery in Wattage Mode

  1. With your battery in Wattage Mode, use the Left Button or Right Button to increase or decrease your wattage. 
  2. Use the following Wattage settings depending on the SOURCE nail atomizer type:
    1. 4 Series SOURCE nail (10mm) Titanium: 20w - 28w
    2. 4 Series SOURCE nail (10mm) Ceramic: 24w - 28w
    3. 4 Series SOURCE nail (10mm) Quartz: 15w - 17w
  3. Once you have selected your desired wattage, you are ready to use your eRig!

Using Your eRig

  1. With your desired temperature or wattage selected, use the included Quartz Carb Cap & Dabber to pick up the material you want to vaporizer. 
  2. Press and hold the Power Button on your battery to start heating up your nail. The SOURCE volt Max has a 15 seconds cut off time, we recommend letting your nail cycle between 7-10 seconds to reach optimum temperatures. 
  3. Place your lips on the mouthpiece of the bubbler, press and hold the Power Button, slowly lower your material into the SOURCE nail atomizer Bucket, and inhale softly.
  4. Once all of the material from your Quartz Carb Cap & Dabber has been placed on the atomizer, flip unto the Quartz Carb Cap and cover the top of the glass bubbler to increase vapor strength and density.
  5. Release Power Button when all material has vaporized.
  6. Repeat Steps 1-5 until completely satisfied. 

How to use with a Water Pipe:

Watch a video on how to connect to your Water Pipe

  1. Take apart the bubbler, and connect the Bottom piece upside down on your SOURCE nail XL attachment in comparison to normal use.
  2. Connect the Bottom piece to your favorite 18mm water pipe!

How to use as a Vape Pen

How to Prep and Power On

  1. Attach the SOURCE nail XL globe to your SOURCE volt Max battery.
  2. Remove the Glass Globe and screw your desired SOURCE nail atomizer clockwise unto the SOURCE nail XL Glass Globe attachment.
  3. Fill your SOURCE nail atomizer with the material you'd like to vaporize (we recommend .2g max).
  4. Replace your glass globe.
  5. Press the Power Button on your SOURCE volt Max battery sequentially 5 times to turn on.

Using Your Vape Pen

  1. Place your lips on the mouthpiece of the glass globe, cover the carb hole on the glass globe with your finger, press and hold the Power Button, and inhale softly
  2. Cover the carb hole on the glass globe with your finger.
  3. Press and hold the Power Button and inhale softly.
  4. Release your finger from the carb hole to increase strength and vapor density.
  5. Release Power Button when all material has vaporized.
  6. Repeat Steps 1-5 until completely satisfied. 
Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request

0 Comments

Please sign in to leave a comment.